A COMPARATIVE ANALYSIS OF VON-MISSES STRESS DISTRIBUTION IN ENGINE SHAFTS

Authors

  • Venkata Sanyasi Seshendra Kumar Karri Department of Industrial Engineering, Gitam University, Visakhapatnam, India

DOI:

https://doi.org/10.53555/eijse.v1i3.78

Keywords:

Dynamic analysis, Von-Misses stress, critical speed, Finite element model

Abstract

In the present work, dynamic analysis is carried out on an engine shaft for a single cylinder four stroke engine. The shafts are modeled using finite element analysis and the intensity of stress magnitude is determined.  It is shown in the paper that the stress variation is high at some critical points. The dynamic analysis is carried out analytically at different engine speeds and is verified by simulation software.  As a result, the critical engine speed and critical region on the shafts are obtained.

References

. C.M.Balamurugan.,R.Krishnaraj.,Dr.M.Sakthive.l,K.Kanthave.l,DeepanMarudachalamM.G.,R.Palani.,2011“Com puterAided Modeling and Optimization of Crankshaft,’’International Journal of Scientific & Engineering Research Volume 2, Issue 8 ISSN 2229-5518

. Yu Ding and Xiaobo Li.,2011, “ Crankshaft Strength Analysis of a Diesel Engine Using Finite Element Method,”Asia-Pacific Power and Energy Engineering Conference

. JianMeng., Yongqi Liu., Ruixiang Liu.,2011,“FiniteElement Analysis of 4-Cylinder Diesel Crankshaft, ” I.J.Image, Graphics and Signal Processing, 5, 22-29

. MENG Jian., LIU Yong-qi., LIU Rui-xiang., and ZHENGBin.,2011,“Intension Analysis of 3-D Finite ElementAnalysis on 380 diesel crankshaft,” International Conference on Computational and Information Sciences

. Yu Gongzh.i, Yu Hongliang. DuanShulin. 2011, “Crankshaft Dynamic Strength Analysis for Marine Diesel Engine,” Third International Conference on MeasuringTechnology and Mechatronics Automation.

. GuYingkui, Zhou Zhibo.,2011,“Strength Analysis of Diesel Engine Crankshaft Based on PRO/E and ANSYS,”Third International Conference on Measuring Technology and Mechatronics Automation

. Xiaorong Zhou., GanweiCai., Zhuan Zhang. Zhongqing Cheng., 2009, “Analysis on Dynamic Characteristics ofInternal Combustion Engine Crankshaft System, “International Conference on Measuring Technology and Mechatronics Automation.

. Farzin H. Montazersadgh and Ali Fatemi., 2007,“DynamicLoad and Stress Analysis of a Crankshaft,” SAE Technical Paper No. 010258, Society of Automotive Engineers

. JonathanWilliams,FarzinMontazersadgh,andAlifatemi.,2007,“FatiguePerformanc Comparison And Life Prediction Of Forged Steel And Ductile Cast Iron Crankshafts,” Publishedin Proceeding of the 27th Forging Industry Technical Conference in Ft. Worth, Texas

. Shenoy, P. S. and Fatemi, A., 2006, “Dynamic analysis of loads and stresses in connecting rods, ”IMechE, Journal of Mechanical Engineering Science, Vol. 220, No. 5, pp. 615-624

. Zoroufi, M. and Fatemi, A.,2005, "A Literature Review on Durability Evaluation of Crankshafts Including Comparisons of Competing Manufacturing Processes and Cost Analysis", 26th Forging Industry Technical Conference, Chicago,

. Prakash, V., Aprameyan, K., and Srinivasan, U.,1998, “An FEM Based Approach to Crankshaft Dynamics and Life Estimation,” SAE Technical Paper No. 980565, Society of Automotive Engineers

. Payar, E., Kainz, A., and Fiedler, G. A., 1995, “Fatigue Analysis of Crankshafts Using Nonlinear Transient Simulation Techniques,” SAE Technical Paper No. 9

Downloads

Published

2015-09-27